• Super tough and durable POM/Nylon construction for maximum performance
• Engineered scoop lifts tyre bead away from the rim with ease
• Recess underneath scoop keeps lever securely in place
• Ergonomic design with thumb grip for maximum control
• Rear spoke hooks to hold lever in place when second lever is used
• Integrated valve core remover
• Compact enough for roadside/trailside repairs and sturdy enough for use in the workshop

• 1 Syringe
• 1 Plastic tubing for syringe/caliper
• 1 Plastic tubing for lever/overflow
• 1 M5 Silver bleed fitting
• 2 M6 Silver bleed fittings
• 1 M7 Black bleed fitting

• Pressure sensitive adhesive ensures the ultimate airtight seal
• Pink, semi-transparent tape for precise application & allows you to locate the valve hole easily
• Engineered stretch & elasticity fits perfectly in the contour of your rim and allows for easy application
• Extreme strength and durability

20 grams of our exclusive size CO2 cartridge. Specifically designed for your larger volume 29ers, mountain and fat bike tires.

These threaded CO2 cartridges are compatible with all of our Genuine Innovations inflators.

Available as single cartridges or a value 6-pack!

• 20 gram threaded CO2 cartridges
• Weight: 73 grams each

The included 9 function Multi Tool contains your most used tools and 
is designed to live inside your stem/steerer tube.

Never get stuck without a Multi Tool on a ride ever again.

• Light weight (Adds just 75g to your bike)
• VERY easy to install in less than 5 mins. 
• Available in  6 colours (Black, Red, Blue, Green, Orange, Purple, Turq)
• No need to remove your star nut or thread your steerer tube.
• Colour matched to our Composite Pedals, Grips and Handlebar Decals.
• Run a single Multi Tool on all your bikes (extra carriers are $15 each)

ENSURE YOUR FORK IS COMPATIBLE -VERY IMPORTANT

Incompatible forks: Giant Overdrive 2 Forks. Rock Shock 35 Gold Forks, Cannondale Lefty Forks. Carbon Steerers

STEERER TUBE INNER DIAMETER

The inner diameter of your steerer tube must be at least 24.1mm. OneUp is not currently aware of any tapered steerer tubes that do not meet this requirement. If fitting unsure, you can check this by inserting the tip of the EDC Lite into the steerer tube above the star nut BEFORE lowering the star nut position.

STEERER TUBE LENGTH  

Most forks are compatible, except for a small number of forks with very short steerer tubes. For the following cases your fork steerer tube length must meet the minimum length requirement.

• Fox except Fox 38 = 190mm (7.5") min
• Fox 38 = 210mm (8.25") min
• RockShox Forks  = 210mm (8.25") min

Measure from the underside of your fork crown to the top of your spacer stack, or top of your stem if you are not running any spacers above your stem.

• 16 function tool: 2 / 2.5 / 3 / 2.5 & 4 (L-type) / 5 / 8 mm Allen wrenches, 4 / 6 mm hex sockets, T10 / T15 / T25 Torx® wrenches, #2 Phillips / flat head screw drivers, 14G / 15G spoke wrenches, CrMo steel chain tool and chain hook 
• Bolts to any standard water bottle boss frame mounts for integrated tools on almost any bike
• Lightweight low-profile design 
• Locking tool case rotates 90 degrees for easy access 
• Solid, secure mounting 

• Engineering grade weatherproof hard shell polymer tool case 
• Durable high-quality Chrome vanadium steel?tools 
• Created in collaboration with Topeak 

- Provides an airtight seal for use with tubeless tire systems.

- Silicon-based adhesive leaves no residue.

- Slick surface assists tire seating during inflation.

• Micro AirBooster and 2 threaded 16g CO2 cartridges 
• Bolts to any standard water bottle boss frame mounts for integrated tools on almost any bike 
• Lightweight low-profile design 
• Solid, secure mounting 
• Created in collaboration with Topeak

The EDC Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer.

Top caps are compatible with all 1-1/8" aluminum steerer tubes.

The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. 

Check fork compatibility.

KIT INCLUDES

• EDC TOP CAP
• EDC steerer plug
• 2x 1mm, 3mm, & 5mm Headset Spacers

INSTALL THE EDC TOP CAP

1. You need a minimum of 5mm of headset spacer above the stem and your steerer tube should be 1-2mm below the top of this spacer.
2. Apply a small amount of grease to your newly cut thread and screw in your new EDC top cap.
3. The Top Cap interface uses a standard cassette lockring tool. You do not need to apply much torque as you are only preloading the bearings. (Your stem pinch bolts are what holds your fork in place). The EDC multitool contains a top cap tightening tool. So even when riding you always have the ability to tighten your headset if need be. 
4. Align your stem and tighten your stem bolts to the manufacturers recommended torque. 
5. The final step is to insert the plastic bung/plug into the bottom of your fork. Turn your 8mm hex sideways and use it to push the plug into the fork by pulling the 8mm towards your chest. This piece holds the bottom of the EDC Tool and stops it from rattling. It also keeps dirt out of your fork and has a small drain hole.

Note* The EDC Tap kit includes a star nut puller and self aligning tap

Patents Pending

All compatibility and fit determinations have been made solely by OneUp. Use of this or any other aftermarket product may void any warranty you have with the original part manufacturer.

A Threadless, no tap install option that lets you store the EDC V2 Tool  inside your stem/steerer tube without threading your steerer tube. EDC Tool sold separately.

The Threadless Carrier replaces your star nut and lets you preload your headset with a bolt, while also creating a space for the EDC Tool.

Easy to install in less than 10 minutes. Install instructions

Available in 8 colours

(Black, Red, Green, Blue, Orange, Purple, Gold & Oil Slick)

Compatible with EDC V2 Tool (You must use the small EDC V2 Storage Capsule with the Threadless Carrier.) The tire plug and bacon strips fit within the small storage capsule.

Chain pliers are not compatible with the threadless carrier set up.

The EDC Threadless Carrier is NOT compatible with V1 EDC Tools (Green Multi-Tool)

ENSURE YOUR FORK IS COMPATIBLE - VERY IMPORTANT

Incompatible forks: Fox 38 with oval steerer (Use a EDC Threaded install), Rock Shox 35 Forks, Giant Overdrive 2 Forks. Cannondale Lefty Forks. Carbon Steerers

STEERER TUBE LENGTH  

Most forks are compatible, except for a small number of forks with very short steerer tubes. For the following cases your fork steerer tube length must meet the minimum length requirement.

• Fox except Fox 38 with oval steerer = 190mm min
• RockShox Forks  = 220mm min
• All other compatible forks = 190mm min

Measure from the underside of your fork crown to the top of your spacer stack, or top of your stem if you are not running any spacers above your stem.